Fix

How to Store Lino Blocks and Flatten a Curled One

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure

Gear for this job

All 7 picks compared
Wooden blocks aligned to spell 'CHECK' with a checkmark symbol on a neutral background
Photo: Ann H on Pexels

Traditional linoleum, the battleship gray lino used for linocut and block printing, keeps changing after it is made. It cures: heat, sunlight and moving air make it harder and more brittle, and a sheet left rolled or leaning takes on that shape. A carved block that was washed too wet can also warp. This page covers the faults that show up in storage, how to rescue a block worth keeping, and how to store carved blocks and spare lino sheets so they stay flat for a reprint.

Curled, hard or cracked lino: causes and fixes

Find what you see in the first column. The rows run from the most common storage problem to the least. Most of them trace back to heat, light, damp or a block that was not kept flat.

How to flatten a curled lino block or sheet

A curl is the most fixable storage fault. The lino has only taken a set, and warmth makes it flexible enough to lie flat again. Use the same gentle heat used before carving: a warm radiator, or a hair dryer moved over the back of the sheet. Essdee, a lino maker, warns that heating and cooling lino too vigorously can cure it and leave it harder, so warm it only until it bends easily. How to soften lino covers the warming methods.

  1. 1

    Lay the sheet on a flat table with the curl facing down. Warm it gently for a minute or two, until it gives under light finger pressure. Do not force it.

  2. 2

    Press it flat by hand, cover it with a clean sheet of paper, then put a board and a stack of heavy books on top so the whole sheet is covered.

  3. 3

    Leave it under the weight until it is fully cool, then check. If the edges lift again, repeat the warming and leave the weight on longer.

  4. 4

    For a sheet that will not stay flat, stick the whole back to thin plywood or foam PVC board with glue or double-sided tape, and weight it while it sets.

Note.A backing board is the lasting fix. One printmaking guide backs lino on Foamex or thin plywood to stop it curving. A mounted block cannot curl again, but check that its new height still suits your press.

Lino gone hard or crumbly with age

Hardness has two causes, and only one is permanent. Cold lino is stiff and softens again with warmth. Cured lino has aged: Essdee describes the hardening as curing and says heat, sun, strong light and air movement all work against the material. Warmth helps a cured sheet a little, but it does not make it new.

Test before you commit a design. Cut a short line in a corner with a sharp V tool. A clean groove with smooth edges means the sheet is usable. Ragged, crumbling edges from a freshly sharpened tool mean the lino is past fine detail. It may still take bold shapes cut with a wide U gouge. Blocks that do not crumble exist: soft cut blocks trade some crispness for an easy cut.

Cracked lino: what can be saved

Brittle lino cracks when it is bent, unrolled cold or lifted by one corner. A crack in an uncarved margin is harmless: trim it off. A crack across the image prints as a thin pale line, because no ink sits in the gap. If the two sides still meet, warm the sheet, flatten it and glue it to a backing board with the crack pushed closed. The line may still show, so pull a proof before printing an edition. If pieces of the surface have flaked off the woven backing, the block is past saving for that design.

Warped blocks and old ink after cleaning

Water causes the last two faults. Lino that is soaked or left wet can warp or swell. Clean a block by wiping it, blot it with a clean dry cloth, and let it dry in the air before it goes into storage. Dried ink left in the cuts builds up, can lift later and fills fine lines on the next printing. Clean the block right after the last print, while the ink is still fresh. The method for each ink type is in how to clean lino blocks and brayers.

How to store lino blocks so they stay flat

The rules are the same for carved blocks kept for a reprint and for spare lino sheets for cutting. Lino bought in bulk or on a roll needs the most care, because it ages while it waits. Buy what you expect to carve fairly soon, and unroll a new roll while it is warm so it can be stored flat.

  • Flat: lay blocks and sheets flat on a shelf or in a drawer, never rolled or leaning on edge. A book or board on top keeps them that way.
  • Clean and dry: no wet ink and no damp. A block put away damp can warp.
  • Cool and dark: keep lino away from radiators, sunny windowsills and strong lights, which cure it.
  • Wrapped or boxed: Essdee advises keeping lino wrapped up. A lidded plastic box also keeps moving air and dust off the blocks.
  • Paper between blocks: a sheet of tissue paper between blocks stops the faces sticking to each other.
  • Labeled: write the title and date on the back or the edge, so the right block is easy to find for a reprint.

When a block is past saving, and what to do with scraps

Replace the lino when a sharp tool tears it instead of cutting, when the surface flakes off the backing, or when a crack crosses the image and shows in a proof. A carved block that has only curled or gone hard is usually worth keeping. Hardness mainly matters for carving, and that work is already done. The block only has to lie flat and take ink.

Offcuts and scraps of good lino are useful. Use them to test a newly sharpened tool, to try a cut before making it on the real block, or to carve small stamps. Store scraps the same way as full sheets. If crumbling was the problem, the soft carving block guide lists rubber and vinyl blocks that do not dry out the same way.

Quick answers

Short answers on keeping carved blocks, spare lino sheets and offcuts flat and in good condition between printing sessions.

  • How do you store lino blocks? Flat, clean and dry, in a cool dark place, wrapped or boxed, with tissue paper between blocks.
  • What can you do with linocut scraps? Test tools and trial cuts on them, or carve small stamps. Keep them flat like full sheets.
  • Is it worth buying linoleum blocks for printmaking in bulk? Only if you will carve them fairly soon. Lino hardens with age, faster in heat and light, so a large stock needs cool, dark, flat storage.
  • How should lino sheets for cutting be kept? Unrolled and flat, wrapped, away from heaters and sun. Warm a cold sheet before you bend it.
  • Can a curled carved block still be printed? Often, yes. Flatten it with gentle warmth and weight, or glue it to a backing board, then pull a proof.

What you need for this

Sources