Tool
Lino Cutting Tool Size Chart: Names, Shapes and Line Widths
What each lino cutting tool is called, how wide it cuts and what it is for. Pick the job to see the shapes that suit it, then read the full table by brand.
Short answer
A lino cutting tool is named by its profile and its width. V tools cut lines and outlines, U gouges clear and texture, a knife cuts edges. Speedball numbers are shape codes, not sizes: 1 small V, 2 large V, 3 small U, 4 square, 5 large U, 6 knife. Pfeil codes give the profile, then the width in mm: L 12/1 is a 60 degree V, 1 mm wide.
Speedball lino cutter numbers and names
| No. | Speedball name | Shape | Used for |
|---|---|---|---|
| 1 | Small V | narrow V | fine lines, outlines |
| 2 | Large V | wide V | outlines, bold lines |
| 3 | Small U | narrow U | textures, clearing tight spots |
| 4 | Square U | flat bottom, upright sides | clearing with a flat floor |
| 5 | Large U | wide U | clearing large areas |
| 6 | Knife | single slanted edge | cutting edges and stop cuts, trimming the block |
The 6-piece set holds one handle and cutters 1, 2, 3, 5 and 6. The 8-piece set holds two handles and all six.
How to read a Pfeil code
| Part of the code | Meaning |
|---|---|
| L | lino and block cutter with a palm handle, blade 70 mm, overall 125 mm |
| B | larger block cutter, blade 80 mm, overall 135 mm (not listed in this chart) |
| 1 | straight chisel, flat edge |
| 1s | skew chisel, flat edge set at a slant |
| 5, 7, 8 | curved gouges, from shallow (5) to deeper (8) |
| 9, 11 | deep gouges; 11 is the narrow U shape Pfeil recommends for fine detail |
| 12 | V-parting tool, 60 degrees |
| 15 | V-parting tool, 45 degrees |
| a after the number | short bent version of the same profile |
| number after the slash | width in mm |
L 12/1 = lino cutter, 60 degree V, 1 mm wide. L 9/5 = lino cutter, deep gouge, 5 mm wide.
Pick the job, see the tools
Choose what you want to cut. The result lists every tool in the chart that suits it, brand by brand, and the link in the address bar keeps your choice.
Shapes for this job
A narrow V, 1 to 2 mm, or the smallest U gouge, 0.5 to 1 mm.
Tools that match
Speedball
Speedball #1
Small V
width not published
Pfeil
Pfeil L 11/0.5
deep gouge, sweep 11
0.5 mm (0.02 in)
Pfeil L 11/1
deep gouge, sweep 11
1 mm (0.04 in)
Pfeil L 12/1
V-parting tool
1 mm (0.04 in)
Pfeil L 15/2
V-parting tool
2 mm (0.08 in)
Flexcut
Flexcut SK803
45 deg. x 1 mm
1 mm (0.04 in)
Essdee
Essdee No. 1
fine lines and cross hatching; 0.5 mm or less in SoftCut, a little wider in lino
0.5 mm (0.02 in) line
Essdee No. 2
universal first tool; lines up to 1.5 mm
1.5 mm (0.06 in) line
Essdee No. 9
deep V for narrow lines
width not published
Power Grip
Power Grip V 1
sankaku (V)
1 mm (0.04 in)
Power Grip V 1.5
sankaku (V)
1.5 mm (0.06 in)
Power Grip Round 1
maru (U gouge)
1 mm (0.04 in)
12 tools in the chart suit fine lines.
Widths are the makers' published figures; Speedball publishes none. The match between tool and job is this site's sorting rule, not a maker rating. Icons are simplified cross-sections, not drawings to scale. Where a maker's instructions differ, they win.
How to read this chart
The picker and the Suits column apply one sorting rule to every tool, from its profile and its published width:
| Job | Tools that suit it |
|---|---|
| Fine lines | V tools up to 2 mm wide; U and deep gouges up to 1 mm wide |
| Outlines | every V tool; knives and skew chisels |
| Textures | curved gouges (U, deep, medium, shallow) from 1.5 to 4.5 mm wide |
| Clearing large areas | curved gouges 5 mm and wider; flat chisels and square cutters of any width |
This is the site's own rule, built on standard practice (V tools for lines and outlines, U gouges for clearing) and on the widths the makers publish. Two brands are handled differently. Speedball publishes no widths, so its six cutters are assigned by name, small or large, as in the table above. Essdee describes what each style is for on its product pages, so Essdee rows follow the maker's own description, not the rule.
Inches are millimeters divided by 25.4, rounded to two decimals. Flexcut publishes its widths in inches, so those rows show the maker's fraction and the millimeters rounded to one decimal.
Lino cutting tools by brand
Showing 61 of 61 tools. Rows that suit fine lines are tinted and marked with a dot.
| Icon | Code | Maker's name | Suits | |||
|---|---|---|---|---|---|---|
| Speedball | #1 | Small V | V, angle not published | not published | fine lines, outlines | |
| Speedball | #2 | Large V | V, angle not published | not published | outlines | |
| Speedball | #3 | Small U | U gouge | not published | textures | |
| Speedball | #4 | Square U | square, flat floor | not published | clearing | |
| Speedball | #5 | Large U | U gouge | not published | clearing | |
| Speedball | #6 | Knife | knife or skew edge | not published | outlines | |
The 6-piece set holds one handle and cutters 1, 2, 3, 5 and 6. The 8-piece set holds two handles and all six. | ||||||
| Pfeil | L 1/4 | straight chiselset LS D | flat chisel | 4 mm (0.16 in) | clearing | |
| Pfeil | L 1/8 | straight chiselset LS A | flat chisel | 8 mm (0.31 in) | clearing | |
| Pfeil | L 1s/4 | skew chiselset LS D | knife or skew edge | 4 mm (0.16 in) | outlines | |
| Pfeil | L 1s/8 | skew chiselset LS A | knife or skew edge | 8 mm (0.31 in) | outlines | |
| Pfeil | L 1a/8 | short bent chiselset LS A | flat chisel | 8 mm (0.31 in) | clearing | |
| Pfeil | L 5/3 | gouge, sweep 5set LS B | shallow gouge | 3 mm (0.12 in) | textures | |
| Pfeil | L 5/5 | gouge, sweep 5set LS D | shallow gouge | 5 mm (0.20 in) | clearing | |
| Pfeil | L 5/8 | gouge, sweep 5set LS A | shallow gouge | 8 mm (0.31 in) | clearing | |
| Pfeil | L 7/4 | gouge, sweep 7set LS D | medium gouge | 4 mm (0.16 in) | textures | |
| Pfeil | L 7/6 | gouge, sweep 7set LS B | medium gouge | 6 mm (0.24 in) | clearing | |
| Pfeil | L 7/10 | gouge, sweep 7set LS B | medium gouge | 10 mm (0.39 in) | clearing | |
| Pfeil | L 8/3 | gouge, sweep 8set LS C | medium gouge | 3 mm (0.12 in) | textures | |
| Pfeil | L 8/7 | gouge, sweep 8set LS C | medium gouge | 7 mm (0.28 in) | clearing | |
| Pfeil | L 8a/7 | short bent gouge, sweep 8set LS D | medium gouge | 7 mm (0.28 in) | clearing | |
| Pfeil | L 9/2 | deep gouge, sweep 9set LS C | deep gouge | 2 mm (0.08 in) | textures | |
| Pfeil | L 9/5 | deep gouge, sweep 9set LS B | deep gouge | 5 mm (0.20 in) | clearing | |
| Pfeil | L 11/0.5 | deep gouge, sweep 11set LS C | U gouge | 0.5 mm (0.02 in) | fine lines | |
| Pfeil | L 11/1 | deep gouge, sweep 11set LS B | U gouge | 1 mm (0.04 in) | fine lines | |
| Pfeil | L 11/2 | deep gouge, sweep 11set LS D | U gouge | 2 mm (0.08 in) | textures | |
| Pfeil | L 11/3 | deep gouge, sweep 11set LS A | U gouge | 3 mm (0.12 in) | textures | |
| Pfeil | L 12/1 | V-parting toolset LS B | V, 60 degrees | 1 mm (0.04 in) | fine lines, outlines | |
| Pfeil | L 12/4 | V-parting toolset LS C | V, 60 degrees | 4 mm (0.16 in) | outlines | |
| Pfeil | L 12a/4 | short bent V-parting toolset LS A | V, 60 degrees | 4 mm (0.16 in) | outlines | |
| Pfeil | L 15/2 | V-parting toolset LS C | V, 45 degrees | 2 mm (0.08 in) | fine lines, outlines | |
The 12-piece set LS 12 holds L 1/8, L 1s/8, L 1a/8, L 5/3, L 5/8, L 7/6, L 7/10, L 9/5, L 11/1, L 11/3, L 12/1, L 12a/4. | ||||||
| Flexcut | SK306 | #6 x 5/16 in | medium gouge | 7.9 mm (5/16 in) | clearing | |
| Flexcut | SK309 | #11 x 1/8 in | U gouge | 3.2 mm (1/8 in) | textures | |
| Flexcut | SK803 | 45 deg. x 1 mm | V, 45 degrees | 1 mm (0.04 in) | fine lines, outlines | |
| Flexcut | SK307 | 70 deg. x 1/4 in | V, 70 degrees | 6.4 mm (1/4 in) | outlines | |
The set has one quick-connect handle, a strop and polishing compound. | ||||||
| Essdee | No. 1 | fine lines and cross hatching; 0.5 mm or less in SoftCut, a little wider in lino | V, angle not published | 0.5 mm (0.02 in) line | fine lines | |
| Essdee | No. 2 | universal first tool; lines up to 1.5 mm | rounded V, angle not published | 1.5 mm (0.06 in) line | fine lines, outlines | |
| Essdee | No. 3 | tight, round cutter; a 2 mm deep-sided line; small circles with a swivel | U gouge | 2 mm (0.08 in) line | textures | |
| Essdee | No. 4 | wide, rounded V; lines 3 mm wide with 45 degree walls | rounded V, 45 degree walls | 3 mm (0.12 in) line | outlines | |
| Essdee | No. 5 | thin line-marking tool for the first lines that define the design | knife or skew edge | not published | outlines | |
| Essdee | No. 6 | flat radius cutter for shallow, wide cuts; circles up to 4 mm in SoftCut | shallow gouge | 4 mm (0.16 in) line | textures, clearing | |
| Essdee | No. 7 | flat-bottomed wide cutter with safety edges; a 3 mm flat trough, clears large areas | square, flat floor | 3 mm (0.12 in) line | clearing | |
| Essdee | No. 8 | wide, deep cutter; lines up to 6 mm | U gouge | 6 mm (0.24 in) line | clearing | |
| Essdee | No. 9 | deep V for narrow lines | V, angle not published | not published | fine lines, outlines | |
| Essdee | No. 10 | like No. 9 with a wider V and a more rounded base; lines up to 3.5 mm | rounded V, angle not published | 3.5 mm (0.14 in) line | outlines | |
| Power Grip | V 1 | sankaku (V) | V, 60 degrees | 1 mm (0.04 in) | fine lines, outlines | |
| Power Grip | V 1.5 | sankaku (V) | V, 60 degrees | 1.5 mm (0.06 in) | fine lines, outlines | |
| Power Grip | V 3 | sankaku (V) | V, 60 degrees | 3 mm (0.12 in) | outlines | |
| Power Grip | V 4.5 | sankaku (V)5-piece and 7-piece sets | V, 80 degrees | 4.5 mm (0.18 in) | outlines | |
| Power Grip | V 6 | sankaku (V) | V, 60 degrees | 6 mm (0.24 in) | outlines | |
| Power Grip | Round 1 | maru (U gouge) | U gouge | 1 mm (0.04 in) | fine lines | |
| Power Grip | Round 1.5 | maru (U gouge) | U gouge | 1.5 mm (0.06 in) | textures | |
| Power Grip | Round 3 | maru (U gouge)5-piece and 7-piece sets | U gouge | 3 mm (0.12 in) | textures | |
| Power Grip | Round 4.5 | maru (U gouge) | U gouge | 4.5 mm (0.18 in) | textures | |
| Power Grip | Round 6 | maru (U gouge)5-piece and 7-piece sets | U gouge | 6 mm (0.24 in) | clearing | |
| Power Grip | Round 7.5 | maru (U gouge) | U gouge | 7.5 mm (0.30 in) | clearing | |
| Power Grip | Round 9 | maru (U gouge) | U gouge | 9 mm (0.35 in) | clearing | |
| Power Grip | Shallow 9 | asamaru (shallow gouge)7-piece set | shallow gouge | 9 mm (0.35 in) | clearing | |
| Power Grip | Flat 7.5 | hira (flat chisel)7-piece set | flat chisel | 7.5 mm (0.30 in) | clearing | |
| Power Grip | Aisuki 7.5 | aisuki (flat clearing chisel)5-piece set | flat chisel | 7.5 mm (0.30 in) | clearing | |
| Power Grip | Skew 7.5 | kiwa (skew knife)5-piece and 7-piece sets | knife or skew edge | 7.5 mm (0.30 in) | outlines | |
| Power Grip | Kamakura 9 | kamakura7-piece set | not described by the maker | 9 mm (0.35 in) | no job assigned | |
5-piece set: round 3 mm, round 6 mm, skew 7.5 mm, aisuki 7.5 mm, V 4.5 mm (80 degrees). 7-piece set: round 3 mm, round 6 mm, skew 7.5 mm, flat 7.5 mm, V 4.5 mm (80 degrees), shallow 9 mm, kamakura 9 mm. Single tools are also made in larger widths: round to 15 mm, shallow gouge 9 to 18 mm, flat and skew 1.5 to 18 mm. US listings of the 5-piece set call the aisuki a straight chisel. | ||||||
Three tools to start with
Most first prints need three cuts: a line, a small scoop and a wide scoop. This is a rule of thumb from the sorting rule above, not a maker recommendation.
| Cut | Speedball | Pfeil | Flexcut SK130 | Essdee | Power Grip |
|---|---|---|---|---|---|
| Small V, 1 to 2 mm | #1 | L 12/1 | SK803 | No. 1 or No. 2 | V 1.5 (the sets hold V 4.5) |
| Small U, 2 to 3 mm | #3 | L 11/2 or L 11/3 | SK309 | No. 3 | Round 3 |
| Wide U or gouge, 5 mm or more | #5 | L 9/5 | SK306 | No. 8 | Round 6 |
Sets built around these three are compared in lino cutting tool sets, and the order of cuts is in how to carve linoleum.
What this chart covers
- Speedball does not publish cut widths for its numbered cutters. They are listed by shape and by small or large, without millimeters.
- Widths are the makers' published figures. Essdee gives the width of the line a cutter makes; Pfeil, Flexcut and Mikisyo give the width of the cutting edge.
- The Suits column is this site's sorting rule from profile and width, except for Essdee, where it follows the maker's own description. It is a guide, not a maker rating.
- Pfeil rows are the 24 L tools in Pfeil's six-piece sets A to D. The larger B tools are not listed.
- Speedball and Essdee do not publish V angles, so those icons are drawn at a nominal angle. Essdee No. 1 and No. 2 are drawn as V cutters after the guide images on the maker's pages.
- The kamakura tool is listed because it is in the Power Grip 7-piece set, but the maker's page does not describe its profile, so it has no icon and no job. English names in brackets on Power Grip rows are this site's translation of the maker's Japanese names.
- Icons are simplified cross-sections, not drawings to scale.
- Inked Block is independent and not affiliated with any tool maker. Where a maker's instructions differ from this chart, the maker's instructions win.
Note.Whatever the tool, cut away from the hand that holds the block and use a bench hook or non-slip mat.
Sources
- Pfeil: catalog, Linoleum and Block cutters
- Speedball: Lino Cutters
- Speedball: 6-piece Lino Cutter Set
- Speedball: 8-piece Lino Cutter Set
- Flexcut: SK130 5pc. Lino and Relief Printmaking Set
- Essdee: Style 1 to Style 10 lino cutters (same URL pattern for styles 2 to 10)
- Mikisyo: Power Grip range
- Mikisyo: Power Grip 5-piece set
- Mikisyo: Power Grip 7-piece set
- Mikisyo: Power Grip V tool
- Mikisyo: Power Grip round gouge