How-to
How to Register a Linocut: 4 Ways to Line Up Colors
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
Short answer
To register a linocut, fix two things for every layer: where the block sits and where the paper lands. A registration sheet with traced outlines does it by eye, a corner jig does it with stops, and 2 pins with 2 tabs taped to each sheet lock the paper in place. For multi-block prints, offset the key block onto the other blocks so they are carved to match.
Gear for this job
All 6 picks comparedWoodzilla Lino Printing Press, A4, Mint
See price on AmazonSee it on AmazonGdaJzh A4 Beech Wood Linocut Press Machine
See price on AmazonSee it on AmazonTOPOWN Mini Linocut Printing Press
See price on AmazonSee it on Amazon

Registration is what makes the second color land exactly on the first. It matters for every multi-color linocut or block print, whether the layers come from several blocks or from one block in a reduction print. A misregistered print nearly always has the same cause: the block or the paper was placed by guesswork. The four methods below run from the least setup to the most. All of them work when printing by hand, and most work on a press. Choose by how many layers and how many prints you plan.
Linocut registration methods compared
The first three methods place the paper on the block. The fourth is different: it makes several blocks carry the same design in the same position, and it is used together with one of the others.
| Method | Accuracy depends on | Hand or press | What you need |
|---|---|---|---|
| Registration sheet | Your eye, and paper all cut to one size | Both | Large sheet of paper, pencil, ruler |
| Corner jig or registration frame | Square paper edges pushed against two stops | Both. On a press, stops must sit lower than the block | Base board, strips fixed at a right angle |
| Pins and tabs | Tabs taped firmly to every sheet | Both. The pins are lower than traditional lino | Board, 2 pins, 2 tabs per sheet, parcel tape, masking tape |
| Key block offset | A clean offset, plus one of the methods above | Both | Carved key block, clear film, blank blocks |
Registration sheet: trace the block and the paper corners
This is the simplest method and needs nothing bought. Handprinted describes it in its reduction linocut tutorial: on a large sheet of paper, draw around the block, then mark where the printing paper should go. It suits small editions of two or three colors printed by hand.
- 1
Cut every sheet of printing paper to exactly the same size, with square corners. The marks only fit one size of sheet.
- 2
On a sheet larger than your paper, draw around the block in pencil. Then draw the outline of the printing paper around it, with the margins you want on all 4 sides.
- 3
For each print, set the inked block inside its outline, inky side up. Hold the paper above it, seat one edge and its 2 corners on the marks, then lower the rest.
- 4
Rub the back with a baren or the flat of your hand without sliding the paper. Lift the print and return the block to its outline for the next sheet.
Note.Tape the registration sheet to the table so it cannot shift while you rub, and wipe stray ink off it before it marks the back of a print.
Corner jig or linocut registration frame
A jig replaces pencil marks with physical stops. Two straight strips are fixed to a flat base board at a right angle, forming an L. The block is pushed into the corner, so it sits in the same spot every time. The paper is registered against a second pair of stops, a fixed distance out from the block. That distance is your margin.
Printmaker Sherrie York describes the handling for her jig: hold the paper above the inked block, slide the bottom edge until it butts against the stop, then slide it sideways until it butts the side stop, and only then let it down. Ready-made registration frames work the same way. A jig is quick for long editions, but it reads the paper edges. The sheets must be square, and the same two edges must go to the stops on every layer.
Pins and tabs on a registration board
Pins and tabs do not depend on the paper edge at all. Each pin is a small flat plate with a raised stud. Each tab is a thin strip with a hole that snaps onto the stud. The tabs are taped to the paper and stay on through every layer. Handprinted's tutorial sets it up like this.
- 1
Take a flat board larger than your paper. Stick the block to it with double-sided tape where you want it, and leave it there for the whole job.
- 2
Tape 2 pins to the board above the block with parcel tape, just beyond where the top edge of the paper will lie. The holes in the pins let the tape grip the board.
- 3
Lay a sheet of paper over the block in position. Leave a little extra paper at the top that can be trimmed off later.
- 4
Snap 2 tabs onto the pins so they overlap the top of the paper. They click into place. Stick each tab to the paper with masking tape.
- 5
Unclip the sheet and repeat for every sheet in the edition, plus a few spares. Each sheet keeps its tabs until the last color is printed.
- 6
To print, ink the block, clip the tabs onto the pins, lower the paper onto the block, and rub the back or run the board through the press.
Note.The pins are slightly lower than a piece of traditional lino, so the board can go through a press. Test the pressure gently first. If you swap blocks between colors, fix a card corner to the board so each block sits in the same spot.
What is a multiple block print, and how to offset a key block
A multiple block print uses a separate block for each color, printed one after another on the same sheet. The layers only line up if every block carries its part of the design in the same position. The offset method does that. You carve the key block first, the block with the main detail or outline, then print it onto each blank block as a carving guide. It replaces transferring the design to each block separately.
- 1
Set up a registration board with a card corner for the block and 2 pins at the top. Cut a sheet of clear polyester film to cover the block and reach the pins, and tape 2 tabs to it.
- 2
Ink the carved key block with water based ink and place it in the corner. Clip the film onto the pins, lower it and rub the back with a baren, a spoon or your hand.
- 3
Lift the film, swap the key block for a blank block in the same corner, lower the film and rub again. The wet image offsets onto the blank block in position.
- 4
Repeat for each color block, inking the key block again each time. Let the offsets dry, carve each block for its color, then print all layers on the same board.
Why the second color lands off
When lino printing layers do not line up, look at the pattern across the edition. The same shift on every print points to the setup. A different shift on each print points to handling.
- The block moved. Stick it down with double-sided tape, or push it firmly into the jig corner before every print.
- The paper was dropped, then nudged. Seat one edge first, lower the rest, and do not slide it once it touches the ink.
- The sheets are not the same size or not square. Edge-based methods need identical paper. Pins and tabs do not.
- The blocks do not match. In a multi-block print, an offset from the key block is the cure. Careful printing cannot fix it.
How to tell the registration is right
Proof before the edition. Print the first color on two or three spare sheets, then print the second color on those spares before touching the good paper. Look along every edge where two colors meet. Good registration shows no white sliver between colors and no overlap line on one side only.
Then print the edition without changing anything on the board. Let each layer dry as the ink needs: the drying time chart gives the range by ink type. A reduction linocut uses the same setup with a single block. On a press, check that nothing on the board stands taller than the block.
Quick answers
Short answers on linocut registration, from what the word means to which setup works on a press and which works by hand.
- What is linocut registration? Placing the block and the paper in the same position for every layer, so the colors line up.
- What is a linocut registration jig or frame? A base board with an L-shaped corner for the block and stops for two edges of the paper.
- What is a multiple block print? A print made from a separate block for each color, printed in turn on the same sheet.
- How do you line up layers in lino printing with multiple colours? Fix the block in one spot and register the paper with marks, stops, or pins and tabs.
What you need for this
- See price on AmazonAmazon
Woodzilla Lino Printing Press, A4, Mint
From Best Hand Presses for Linocut and Block Printing at Home
- See price on AmazonAmazon
Speedball block printing baren, 4 in
From Best Barens for Linocut and Block Printing Without a Press
- See price on AmazonAmazon
Speedball Printmaster paper, 9 x 12 in, 50 sheets