Explainer
Lino Cutting Safety: Bench Hooks, Hand Guards and Safe Technique
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
Short answer
The typical lino cutting injury is a slip: the tool jumps out of the cut and into the hand holding the block. Keep that hand behind the blade and cut away from it, hold the block with a bench hook or non-slip mat, keep tools sharp, warm stiff lino and take shallow cuts. No tool, guard or glove is injury-proof.
Gear for this job
All 6 picks comparedSpeedball 4131 Linoleum Cutter Set, 5 Types
See price on AmazonSee it on AmazonEssdee lino cutter set with safety hand guard
See price on AmazonSee it on AmazonJoygineer Linocut Kit for Printmaking
See price on AmazonSee it on Amazon

This page is for anyone starting to carve, and for parents and teachers setting up a lino printing session for children. The rules below are the standard ones, stated the way tool makers and printmaking references state them, in order of how much each one matters. They lower the risk of a cut. They do not remove it. Carving is the main hazard in lino printing and block printing, so most of the page is about the blade. A shorter section at the end covers ink and cleanup, where the point to watch is solvent.
The 5 lino cutting safety rules, most important first
Each rule removes one way for a slip to end in a cut. The first two do most of the work: if the holding hand is never in front of the blade, a slip has nothing to hit.
| Rule | What it prevents | How sources put it |
|---|---|---|
| 1. Holding hand behind the blade, cut away from it | The tool slipping into your fingers | Essdee: always carve away from your hand and fingers |
| 2. Bench hook or non-slip mat under the block | The block sliding as you push | Letterpress Commons: brace on non-slip matting or use a bench hook |
| 3. Keep tools sharp | Forcing the tool until it jumps | A dull tool needs more force and is harder to control |
| 4. Warm stiff lino gently | Extra force on a hard, cold block | Essdee: a radiator or hair dryer, but too much heat hardens lino |
| 5. Shallow cuts at a low angle | The tool digging in, then breaking free | Essdee: a shallow angle between cutter and block, without excess force |
Where does the holding hand go?
Behind the cutting hand, always. A letterpress reference puts the rule in two parts: never carve toward your hands or body, and brace the block behind your carving hand with downward pressure. In practice the holding hand rests on a part of the block that the tool has already passed, or will not reach on this stroke.
When a line curves toward your holding hand, stop and turn the block, not the tool. Turning the block keeps every cut pointing away from you. Essdee notes that many people carve toward the hand that holds the work, which is the habit to break in the first session. The cuts themselves are covered in how to carve linoleum.
Note.One printmaking guide advises keeping a first aid kit nearby while carving. That is as far as the sources go, and this page adds no first aid advice of its own.
What a bench hook does, and when a non-slip mat is enough
A bench hook is a board with a lip underneath that catches the edge of the table and a rail on top that the block rests against. You push the tool toward the rail, so the force of the cut holds the block in place instead of sliding it. Essdee describes its bench hooks as keeping the work steady, placed on the edge of the desk, with rails that can be refitted for left or right hand use. It sells them as 300 x 200 mm and 300 x 400 mm.
A non-slip mat does the first half of that job: it stops the block skating on the table. It has no rail to push against, so the holding hand still has to brace the block from behind. Traditional lino takes more pressure to cut than a soft block, and more pressure is where a rail earns its place.
Linocut hand guards and gloves
A hand guard is a shield for the holding hand. Essdee's version is held at the corner or top of the block, close to the area being cut, and has upright walls that catch the tool if it slips. The maker says it fits small and large hands, works left or right handed, and is meant for people new to lino cutting, younger artists and those with limited dexterity.
Gloves are a different matter. None of the tool maker pages checked for this site recommends a glove for carving: their answers are hand position, a bench hook and a guard. If you choose to wear a cut-resistant glove on the holding hand, treat it as a backup only. It does not change rule 1, and no glove or guard is injury-proof.
Why sharp tools and warm lino count as safety rules
Force is what turns a slip into an injury. A dull edge tears or skids instead of cutting, so you push harder, and a tool under a heavy push travels a long way when it breaks free. One carving guide states it plainly: a dull tool requires more force, which makes it harder to control. Strop solid gouges often and replace worn push-in blades: how to sharpen lino cutting tools covers both.
Cold or old lino has the same effect as a dull tool. Traditional lino needs more pressure when it is cold and turns dry and crumbly with age. Gentle warmth from a radiator or a hair dryer softens it, but do not overdo it, since too much heat hardens lino. See how to soften hard lino. Then keep the cuts shallow: the same carving guide gives 1 to 2 mm as deep enough for a clean channel.
Lino cutting tools for kids and for schools
Children carve with an adult supervising for the whole session. The five rules apply unchanged. What changes is the material and the kit. Soft rubber and vinyl blocks carve with little pressure, so there is less force behind any slip, and Speedball aims its Speedy-Cut block at young students and beginners.
For classroom and family sets, see lino cutting tools and kits for kids. No kit makes carving risk-free.
- One bench hook or non-slip mat per carver, set up before the tools are handed out.
- A hand guard for each holding hand, placed close to the area being cut.
- Soft blocks in place of traditional lino, so cuts need little pressure.
- Sharp, undamaged cutters: a dull tool is the one that gets forced.
Lino printing health and safety: ink, solvents and cleanup
Most inks sold for printing at home clean up without solvent. Water based block ink washes off with soap and water, and water-washable oil based inks such as Caligo Safe Wash clean up with liquid soap, then water. The block printing ink chart lists cleanup for each ink type.
Traditional oil based ink is the exception: it is cleaned with a solvent such as white spirit. Use solvents with ventilation and follow the label, including any gloves it calls for. Keep solvents off rubber rollers, and dispose of used solvent as your local rules require.
Quick answers
Short answers to the lino cutting safety questions people search for. The reasoning behind each one is in the sections above.
- What is the main rule of lino printing safety? Keep the holding hand behind the blade and cut away from it. Every other rule supports that one.
- Is a linocut hand guard needed? It is optional. It shields the holding hand and suits beginners and children, but it does not replace safe hand position.
- Are linocut gloves worth wearing? Only as a backup. The maker pages checked recommend hand position, a bench hook and a guard, not gloves.
- Which lino cutting tools are suitable for kids? Sharp cutters on soft blocks, with a bench hook, a hand guard and an adult supervising. No tool is injury-proof.
- What do lino cutting tools for schools need alongside them? A bench hook or mat and a hand guard per pupil, soft blocks, and ink that cleans up with soap and water.
What you need for this
- See price on AmazonAmazon
Speedball 4131 Linoleum Cutter Set, 5 Types
From Best Lino Cutting Tools and Block Printing Kits for Kids
- See price on AmazonAmazon
SGHUO Pink Rubber Linoleum Blocks, 4x6, 12 Pcs