Woodcut vs Linocut: Differences in Tools, Effort and Print

Published Updated

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure

Gear for this job

All 7 picks compared

Linocut is easier to carve and better for beginners, while woodcut is harder to carve but gives a textured print that shows the grain of the wood. Both are relief printing: you cut away the white areas, ink the raised surface and press paper onto it. The choices that matter are the block, the tools and how much effort you want to put into the carving. This article compares the two on those points and says which one to start with.

The short version of the differences

Both are relief prints: you cut away what should stay white, ink the raised surface and press paper onto it. The differences are all in the block. Linoleum is a uniform, grainless material that cuts the same way in every direction. Wood has a grain, which guides the blade in one direction, fights it in another, and often shows up in the print as faint streaks and texture.

That single fact explains most of what follows. Lino forgives a wobbly hand and rewards curved, flowing lines. Wood asks for planning around the grain, sharper tools and more force, and pays you back with a print that looks unmistakably hand made.

Carving feel and effort

Lino cuts like firm cheese: the blade moves in any direction with little push, and a soft-cut or rubber block is easier still. This is why nearly every beginner kit is built around lino, and why kids classes use it. A shallow tool angle and light pressure are enough, and mistakes come from slipping, not from the material fighting back.

Woodcut takes more effort. Along the grain a sharp gouge slices cleanly, but across the grain the edge can chip or tear fibers out, and thin raised lines can snap off. Hardwoods such as cherry, pear and maple hold fine detail well and cut slowly. Softer woods and plywood cut faster but tend to break at the edges of narrow lines. Expect shorter carving sessions and more sharpening than with lino.

Tools: lino cutters or palm gouges

Lino tools have a U or V shaped blade set in a handle, and they work in wood only on the softest woods. A real woodcut asks for a stiffer blade: palm gouges, V-parting tools and flat or skew chisels, held in the palm and pushed with the arm. They stay keen for longer on wood, but need honing on a strop or stone. Sets from Flexcut, Pfeil and Japanese makers are the usual choices.

If you already own lino cutters, you do not need to replace them to try a woodcut on soft wood, but a small palm set makes the work a lot easier. The wood tools guide compares seven sets by shapes, widths and steel, and the sharpening article covers keeping the edges in shape.

Compare wood carving tools for woodcut →

What the print looks like

A lino print tends toward flat, solid blacks and clean white shapes, with crisp edges. Large inked areas print evenly when the block is rolled well. The main flaw is a slightly mottled surface where the ink did not transfer, which is a rolling and pressure issue rather than a material one.

A woodcut shows the grain. On plank wood, the lines of the grain can appear as streaks in solid areas, and some printmakers choose the wood just for that effect. If you want clean solids, plywood with a smooth face or a very fine-grained hardwood is the safer choice, and a lighter hand with the ink helps. Knots and gaps in cheap plywood print as flaws, so check the face before you start.

Inks, paper and printing are the same

Once the block is cut, the printing is common to both. Water based ink and oil based ink both work on lino and wood, and a brayer rolls out a thin, even layer on either. Paper and pressure matter more than the block: a baren or a press, and a paper in the weight range printmakers use for relief work. Wood is harder than lino, so it takes more pressure to print solids evenly, and a press helps.

The same cleanup applies too, but wood soaks up water and oil more than lino, so wipe a woodblock rather than soaking it, and let it dry flat to avoid warping.

Compare brayers for relief printing →

Which should you start with?

Start with lino or a soft carving block if you want a quick first print, are cutting small designs, or are working with a child. The lessons carry over: reading a design in reverse, thinking in positive and negative, rolling ink evenly, and registering colors.

Move to woodcut when you want a bolder texture, larger blocks or a particular rustic look, and you are happy to buy a few better tools and sharpen them. Many printmakers keep both going: lino for fast cards and multi-block color work, wood for the pieces where the grain is part of the design.

See soft carving blocks →

Starting with linocut?

Start with lino or a soft carving block if you want a quick first print and are cutting small blocks. A beginner kit puts block, cutter, ink and more into one box, but what is in the box differs more than the titles suggest. Our beginner kit guide compares what each box includes.

Compare beginner linocut kits →

Frequently asked questions

Is woodcut harder than linocut? Yes, for most people. Wood has a grain that changes how the blade behaves, it needs sharper and sturdier tools, and mistakes such as chipped lines cannot be undone. Lino is more forgiving, which is why it is the usual starting point.

Can I use lino cutters on wood? Only on very soft wood, and with care. Lino blades are thin and made for a soft material, and on harder wood the edge dulls quickly or the tool can snap. For regular woodcut, palm gouges and chisels are the better match.

What wood is best for woodcut printing? Fine-grained hardwoods such as cherry, pear and maple are traditional choices, and birch or shina plywood is a common cheaper option. Choose a smooth, flat piece without knots, and sand the face before you carve.

Do I need a press for woodcut? No. You can print woodcuts by hand with a baren or a wooden spoon, which is the traditional method for Japanese woodblock prints. A press makes it easier to get solid, even blacks on a hard block.

What you need for this