# How to Sharpen Lino Cutting Tools: V Gouges, U Gouges and Blades

Source: https://inkedblock.com/blog/how-to-sharpen-lino-cutting-tools
Published: 2026-10-01
Publisher: Inked Block

**Short answer:** A lino tool that tears, skids or needs force is dull. For solid gouges, keep the factory bevel, hone the outside on a fine stone, remove the burr inside with a shaped slip, then strop. After that, strop about every **15 to 20 minutes** of carving. Thin push-in cutters are replaced, not sharpened: Essdee says its cutters are not designed to be sharpened.

This page is for a carver whose tool has started to tear the lino. Two things decide the fix. The first is the kind of tool: a solid gouge from Pfeil, Flexcut or Power Grip is made to be kept sharp, while a thin cutter that pushes into a handle is a consumable. The second is how far gone the edge is: a tool that has just lost its bite needs only a strop, and a nicked or rounded edge needs a stone first. Linoleum dulls steel quickly, so sharpening is a routine, not a repair.

## Lino tool tears, skids or needs force: causes and fixes

Start with the top row. Most problems are an edge that needs a strop, and the lower rows only apply if stropping does not bring the cut back. Check the lino too: a cold or old block tears under a sharp tool.

| What you see | Likely cause | What to do |
| --- | --- | --- |
| Tool needs more force than it did | Edge has lost its keenness | Strop outside and inside, then try it on scrap lino |
| Tool skids across the surface before it bites | Dull or slightly rounded edge | Strop. If no better, hone on a fine stone, then strop |
| Tears or crumbles the edge of the cut | Dull edge, or cold or old lino | Strop the tool, warm the lino gently, try a fresh block |
| Ragged line on one side of a V cut | One wing duller, or a burr left inside | Equal strokes on both wings, then clear the inside with a slip |
| Still tears after stropping | Nick or rounded bevel | Hone on a stone at the factory bevel, remove the burr, strop |
| Push-in cutter drags or tears | Thin replaceable blade is worn | Fit a new cutter |

Ordered from most to least likely for a tool that used to cut cleanly.

## Which lino tools can be sharpened, and which blades are replaced?

Check this before buying a stone. Makers treat their tools differently, and the split runs between solid tools and thin cutters that push into a handle. For the shapes and sizes each brand makes, see the [lino cutting tool size chart](https://inkedblock.com/tools/lino-cutting-tool-size-chart).

| Tool | What the maker says | Do this |
| --- | --- | --- |
| Essdee push-in cutters | Not designed to be sharpened. Replacements come in multipacks | Replace |
| Speedball lino cutters | No sharpening instructions. Cutters swap in the handle's chuck | Usually replaced |
| Flexcut SK130 blades | The set includes a strop and polishing compound | Strop, hone when needed |
| Pfeil L tools | Sold sharpened and ready for use | Hone and strop |
| Power Grip (Mikisyo) | Can be sharpened and used for a long time | Hone and strop |

From the makers' own pages. Where a maker gives no sharpening instructions, the cell says so.

Note: Essdee's reason for replacing: sharpening such small cutters takes skill and risks damaging them. Speedball handles unscrew at the end to store spare cutters.

## How to sharpen a U gouge

A gouge has one bevel, on the outside of the curve. The inside stays flat along its length: nothing is ground there, it is only cleared of the burr. One guide puts lino tool bevels at roughly 20 to 30 degrees, but you do not need to measure. Rest the existing bevel flat on the stone and keep that angle.

1. Set a fine stone on a damp towel so it cannot slide. A supplier guide suggests a fine side of 3000 to 6000 grit. If it is a soaking water stone, give it 10 to 15 minutes in water first.
2. Lay the bevel flat on the stone and roll the tool from one corner of the curve to the other as you move it, so the whole edge touches. Use light pressure and a few strokes at a time.
3. Stop when an even, bright band runs along the whole edge. Honing the outside pushes a fine burr of steel over to the inside.
4. Clear the burr with the rounded edge of a fine slip stone, about 4000 grit, held flat in the channel. Work from the center outward with a few light passes.
5. Strop: draw the tool backward along a leather strop charged with compound, rocking it so the whole curve touches. Then strop the inside on a rounded profile.

Note: Never sharpen toward your body. Move the blade away from yourself, and keep the hand that steadies the stone behind the edge.

## How to sharpen a V tool

A V tool is two flat bevels that meet at a point, so treat each wing as a small flat chisel. The risk is uneven work: more strokes on one wing wear it back further than the other, and the tool starts to cut a lopsided line. Count your strokes.

1. Lay the bevel of one wing flat on the fine stone and hone it with light strokes, keeping the factory angle. Count the strokes.
2. Turn the tool and give the other wing exactly the same number. The supplier guide's rule for stropping applies here too: ten on one side means ten on the other.
3. Clear the inside with the pointed edge of a slip stone laid into the V, a few light passes along each inner face.
4. Strop each outer bevel with equal strokes, drawing the tool backward. Then strop the inside on a V-shaped profile, such as the one on a molded slip strop.
5. Try it on scrap lino: a sharp V cuts a clean line with light pressure and leaves both edges of the line smooth.

## How often to strop, and which sharpening tool to use

Stropping is what keeps a tool sharp between sessions on the stone. One supplier guide says to strop about every **15 to 20 minutes** of carving, and a letterpress reference advises keeping a leather strop with honing compound within reach for the whole session. Draw the blade backward, edge trailing, with firm pressure. Pushed edge first, the tool digs into the leather.

A strop needs compound to work: the supplier guide names chromium oxide, applied sparingly to the leather. For the inside of V tools and gouges you need a shaped surface. Flexcut's SlipStrop is molded for polishing and deburring the inside of V-tools and gouges as well as the outside bevel, and comes with a bar of polishing compound. A fine slip stone with one rounded and one pointed edge does the same job at the honing stage.

## When the lino is the problem, not the tool

A sharp tool still tears a block that is cold or past its best. Traditional lino needs more pressure when cold and turns dry and crumbly with age. If a freshly stropped tool crumbles the edge of a line, warm the block gently on a radiator or with a hair dryer and try again: [how to soften hard lino](https://inkedblock.com/blog/how-to-soften-lino) has the method. If warm lino still crumbles, the block is old. Storage that slows this down is covered in [how to store lino blocks](https://inkedblock.com/blog/how-to-store-lino-blocks).

## How to keep lino tools sharp for longer

Edges are lost in storage as well as in use. Pfeil advises keeping tools in a roll, box or rack where they cannot knock against each other or fall, in a dry room, with a light coat of oil for long storage. Loose cutters rattling in a drawer lose their edges the same way, which is why a handle with storage inside is worth using.

- Strop about every 15 to 20 minutes of carving, before the tool starts to tear.
- Go back to the stone only when stropping stops working. Every honing removes steel.
- Keep the stone on a damp towel so it stays put, and sharpen away from your body.
- Do not force a dull tool. More force means less control: see [lino cutting safety](https://inkedblock.com/blog/lino-cutting-safety).

## Quick answers

Short answers on sharpening lino cutting tools. The full steps for U gouges and for V tools are in the two step sections above.

- **How do you sharpen lino tools?** Keep the factory bevel, hone the outside on a fine stone, clear the inside burr with a slip, then strop.
- **How do you sharpen linocut tools with push-in blades?** You usually do not. Essdee says its cutters are not designed to be sharpened: fit a new one.
- **Which linocut sharpening tool is needed?** For upkeep, a leather strop with compound and a shaped profile for the inside. A fine stone and a slip stone handle real dullness.
- **Is there a linocut tool sharpener for V and U tools?** Yes. A molded slip strop, or a slip stone with a rounded and a pointed edge, reaches inside both shapes.
- **How often does sharpening lino cutting tools come up?** Strop about every 15 to 20 minutes of carving. Hone on a stone only when stropping no longer restores the cut.

## Gear guides for this topic

- https://inkedblock.com/best/best-professional-lino-cutting-tools
- https://inkedblock.com/best/best-japanese-lino-cutting-tools
- https://inkedblock.com/best/best-lino-cutting-tool-set

## Sources

- [Hickman Design: How to Sharpen and Maintain Your Lino Cutting Tools](https://hickmandesign.co.uk/blog/equipment/how-to-sharpen-and-maintain-your-lino-cutting-tools/)
- [Essdee: Frequently Asked Questions](https://www.essdee.co.uk/frequently-asked-questions/)
- [Flexcut: SlipStrop](https://www.flexcut.com/home/product/pw12-flexcut-slipstrop)
