# How to Clean Dried Ink Off Lino Blocks, Brayers and Slabs

Source: https://inkedblock.com/blog/how-to-clean-lino-blocks-and-brayers
Published: 2026-10-01
Publisher: Inked Block

**Short answer:** Match the cleaner to the ink. Dried water based block ink stays water-soluble, so warm water and a little dish soap lift it. Water-washable oil ink needs liquid soap worked into the ink first, then cold water. Speedball's oil-based relief inks clean up with vegetable oil or solvents. Never soak lino, and keep solvents off rubber brayers.

Cleanup goes wrong in two ways: it was left too long, or the wrong cleaner met the wrong surface. Ink left overnight on a brayer (the roller), a block or an inking slab is one problem. A brayer that has turned sticky or grown a flat side, or a lino block that has warped, is damage from the cleanup itself. Find what you see in the table, then read the section for your ink type. Every cleaner and caution here is the one the ink or roller maker states for its own product.

## What you see, the likely cause and what to do

The rows run from the most common problem to the least. The first three depend on the ink, so check the tube: water based, water-washable oil, or oil based with vegetable oil or solvent cleanup.

| What you see | Likely cause | What to do |
| --- | --- | --- |
| Dried water based ink on the block, brayer or slab | Cleanup was left until later | Wet it with warm water and a little dish soap, let it soften, wipe. Do not soak the lino |
| Greasy film that smears after washing | Water-washable oil ink met water before soap | Put liquid soap straight on the ink, wipe, then rinse with cold water |
| Dried oil ink that soap will not move | Oil ink has hardened. Soap only works while it is wet | Makers give no method for hardened ink. Try the cleaner on the ink label. Keep solvent off rubber |
| Brayer rubber feels sticky or soft | Solvent used on the rubber | Stop using solvent. Wash with detergent and water. Replace the roller if it stays tacky |
| Flat spot or dent on the brayer | Stored resting on its rubber | Hang it or rest it on its back. Replace it if the dent prints as a stripe |
| Lino block warped or swollen | Block was soaked or left wet | Wipe, never soak. Blot dry and store flat |

Cleanup problems on lino blocks, brayers and inking slabs. Cleaners are those the ink and roller makers name for their own products.

## Dried water based block printing ink: soap and water

Water based block ink stays water-soluble after it dries. That is a weakness in a finished print and a help at the sink: dried ink softens again when it is wet. Speedball states soap and water for its Water-Soluble Block Printing Ink. Essdee states warm water, with a little dish detergent if you wish, for its rollers and ink trays.

A slab, tray or brayer can go under the tap. A lino block cannot sit in water. Wet a sponge or soft brush with soapy water, work over the block, give the dried ink time to **soften** and wipe again. A soft brush clears ink from the cut lines without scratching the surface. Blot the block dry with a cloth right away.

## Water-washable oil based block printing ink: soap first

Caligo Safe Wash and similar inks are oil inks that soap can break down. Water alone cannot. Cranfield's order is: take off the excess ink with a rag or by rolling it out on old newspaper, put liquid soap or detergent **directly onto the ink** with a rag, brush or soft sponge, then wipe away the mix with a damp sponge and rinse with fresh water. Cranfield says to use cold water, not hot, and warns that water with no soap may leave ink residue. That residue is the greasy film in the table.

Speedball gives soap and water or window cleaner for its Professional Relief Ink. All of this applies to wet ink. Once an oil ink has dried hard, soap no longer shifts it, which is the reason to clean up the same day. How the ink types differ is covered in [oil based vs water based ink](https://inkedblock.com/blog/oil-based-vs-water-based-block-printing-ink).

## Oil based ink that needs oil or solvent

Speedball states that its Oil-Based Relief Inks clean up with vegetable oil or solvents, and that they need one or the other for a proper cleanup. Its page names no particular solvent, so the label of the ink and of the solvent you buy decides the rest. Use any solvent with ventilation and follow that label.

Vegetable oil is the option Speedball names that is not a solvent. If you use it on a rubber brayer, wash the oil off afterwards with dish soap and water, and check the care notes of the roller's maker. Essdee is blunt about solvents. It says not to use white spirit, turpentine or anything described as a solvent on its rollers, because solvents break rubber down. None of the maker pages checked gives a method for oil ink that has fully hardened on a block.

Note: Check the cleanup line on the tube before buying oil based ink. The [ink chart](https://inkedblock.com/tools/block-printing-ink-chart) lists cleanup for each ink type, as the makers state it.

## Brayer roller gone sticky or flat on one side

Both faults come from care, not from printing. Essdee's explanation for a roller that degrades is solvent: used on rubber or rubber-like material, it causes the material to break down. Stop using solvent and go back to detergent and water. If the surface still feels tacky after that, it will pick up dust and lay ink unevenly, and the roller needs replacing.

A flat spot or dent comes from weight on the rubber. Essdee recommends hanging the roller by the hole in its handle, or resting it on its back so the rolling surface touches nothing. Speedball's brayer pages give no care instructions, so the same habit is the safe default. A dent can print as a pale mark once every turn. Replacements are compared in [brayers for block printing](https://inkedblock.com/best/best-brayer-for-block-printing).

## Lino block warped after washing

Lino should never be soaked. A block that is waterlogged or left wet can warp or swell, and a warped block is hard to print evenly. Clean it with a damp sponge, not under a running tap, blot it dry and let it finish drying flat. Clear the cut lines with a soft brush while the ink is still wet, because dried ink is hardest to remove from there. How to flatten a curled block is in [how to store lino blocks](https://inkedblock.com/blog/how-to-store-lino-blocks).

## How to stop ink drying on your tools

Clean up as soon as the last print is pulled. For a brayer, this is the routine Essdee gives for its rollers. It is short, and it prevents most of the rows in the table above. Good rolling habits are in [how to use a brayer](https://inkedblock.com/blog/how-to-use-a-brayer).

1. Roll the brayer on old newspaper until it leaves almost no ink. This removes most of the ink before any water or soap is involved.
2. Work liquid detergent into the rubber with your fingers. For water-washable oil ink this soap step comes before any water touches the ink.
3. Rinse under a running tap until the water runs clear. Use warm water for water based ink and cold water for water-washable oil ink.
4. Tap the water out of the roller's bearings and dry the frame, so no water is left to drip onto the next slab of ink.
5. Hang the brayer by its handle or rest it on its back, with the rubber touching nothing. Wipe the block, blot it dry and store it flat.

## Quick answers

Short answers by ink type and tool. If the label on your ink, block or roller says something different, follow the label.

- **How do you clean block printing ink that is water based?** Soap and water, as Speedball and Essdee state. Dried ink softens again when wet, so wet it, let it soften and wipe.
- **How do you clean oil based block printing ink?** Water-washable oil ink: liquid soap on the ink first, then cold water. Speedball Oil-Based Relief Ink: vegetable oil or solvents.
- **Can you use solvent on a brayer roller?** Not on rubber. Essdee says white spirit, turpentine and other solvents break the rubber of its rollers down.
- **How do you store a brayer roller after cleaning?** Hang it by the handle or rest it on its back, so the rubber touches nothing and cannot dent.
- **Can you soak a lino block to clean it?** No. Waterlogged lino can warp or swell. Wipe it with a damp sponge and blot it dry.

## Gear guides for this topic

- https://inkedblock.com/best/best-brayer-for-block-printing
- https://inkedblock.com/best/best-water-based-block-printing-ink
- https://inkedblock.com/best/best-oil-based-block-printing-ink

## Sources

- [Essdee: Frequently Asked Questions](https://www.essdee.co.uk/frequently-asked-questions/)
- [Cranfield Colours: FAQs](https://www.cranfield-colours.co.uk/faqs/)
- [Speedball: Oil-Based Relief Inks](https://www.speedballart.com/oil-based-relief-inks/)
